Ultracur3D® Cleaner Resin printing cleaning solvent Ultracur3D® Cleaner is used for cleaning of SLA/DLP/LCD printed ‘green’ parts, prior to post curing, it removes residual uncured resin and other surface contaminations. The time required for cleaning depends on the type of resin, the temperature, the agitation (e.g. ultrasound) and the complexity of the part. Description Ultracur3D® Cleaner is non-harmful, non-flammable at room temperature and can be heated up to 50 °C to increase cleaning efficiency. This cleaner is suitable for industrial part washing and cleaning equipment. Ultracur3D® Cleaner can normally be used until it contains about 10-20% of resin, or until the cleaning performance is noticeably reduced. After this, it should be disposed according to local regulations. Extensive soaking of parts in Ultracur3D® Cleaner can influence the final properties of the part. High shear agitation using ultrasound, turbulent mixing or other
Ultracur3D® Cleaner
Resin printing cleaning solvent
Ultracur3D® Cleaner is used for cleaning of SLA/DLP/LCD printed ‘green’ parts, prior to post curing, it removes residual uncured resin and other surface contaminations. The time required for cleaning depends on the type of resin, the temperature, the agitation (e.g. ultrasound) and the complexity of the part.
Description
Ultracur3D® Cleaner is non-harmful, non-flammable at room temperature and can be heated up to 50 °C to increase cleaning efficiency. This cleaner is suitable for industrial part washing and cleaning equipment.
Ultracur3D® Cleaner can normally be used until it contains about 10-20% of resin, or until the cleaning performance is noticeably reduced. After this, it should be disposed according to local regulations.
Extensive soaking of parts in Ultracur3D® Cleaner can influence the final properties of the part. High shear agitation using ultrasound, turbulent mixing or other appropriate device will influence the cleaning performance and final part quality.
Specific Benefits
Effectively removes 3D printing resins
Water rinseable
Non-flammable at room temperature
No damage to ‘green’ part or cured resins when used as recommended
Material Properties
Liquid Color: Blue
Odur: Ether like
pH value: 7 (25 °C)
Melting Point: > 50 °
Boiling Point: > 100 °C
Vapour Pressure: 0.017 hPa (20 °C)
Density: 1.09 g/cm3 (20 °C)
Viscosity @ 20 °C: mPa·s (cP) 5
Cleaning procedure
Immerse the part in an agitated bath of Ultracur3D® Cleaner for a maximum of 10 minutes. Typical cleaning time is recommended between 5 to 8 minutes. Some require cleaning below 5 minutes.
Rinse with 2-propanol for additional 1-3 minutes
2-propanol can be blown off with pressured air or parts can be dried at ambient temperature. For accelerated drying heat the part for approximately 10 minutes at 60 °C (140 °F)
Tested Compatibility with Ultracur3D® resins:
Ultracur3D® DMD 1005
Ultracur3D® EPD 1006
Ultracur3D® EPD 1086
Ultracur3D® EPD 2006
Ultracur3D® EPD 3500
Ultracur3D® EPD 4006
Ultracur3D® RG 35
Ultracur3D® RG 50
Ultracur3D® ST 45
Ultracur3D® ST 45 B
Ultracur3D® ST 45 M
Ultracur3D® ST 80
Ultracur3D® EL 60
Ultracur3D® FL 60
Next Steps
Material Details
User Guidelines
BASF Ultracur3D Cleaner
U3DPS BASF - Ultimate 3D Printing Store
What are the Innovations to Come in 3D Printing?
BASF Forward AM Resins Validated on Zortrax Inkspire 2
BASF - Ultracur3D ST 80 - Gray– Ultimate 3D Printing Store
BASF Ultracur3D Reative Urethane Photopolymer Water Washable Resin
U3DPS BASF - Forward AM Ultracur3D® 3D Printing Resins– Ultimate
Shining 3D Accufab L4K Resin 3D Printer - Buy Shining 3D 3D
BASF Ultracur3D Reative Urethane Photopolymer Water Washable Resin
Ultracur3D® ST 80 W, Multi-Purpose Resin Targeting the Lowest Cost per Part, Ultracur3D® ST 80 W (White) by Forward AM is a reactive urethane
BASF - Ultracur3D ST 80 - White
Supplementary Line - BASF FORWARD AM
Ultracur3D® ST Tough Resin Photopolymer
Shop By Material 3D Printer Filament, Resin, Powder
Shop By Material 3D Printer Filament, Resin, Powder
Ultracur3D® CK (Color Kit) Enabling parts in a wide range of colors without the need for post-processing The BASF color kit solutions allow to print
BASF - Ultracur3D CK - Resin Color Kit